A detached breakwater is a structure parallel, or close to parallel, to the coast, build inside or outside the surf zone. Detached breakwaters are mainly built with two purposes, either to protect a ship wharf from wave action or as a coast/shore protection measure.
Detached breakwaters are used as shore and coast protection measures. In general terms, a detached breakwater is a coast-parallel structure located inside or close to the surf-zone. This article discusses aspects of breakwaters as coastal protection, as well as their impacts in causing erosion.
- 1 Variable of breakwater schemes
- 2 Purpose of a breakwater
- 3 Defining a detached breakwater
- 4 Functional characteristic of emerged detached single breakwaters
- 5 Impacts of breakwaters
- 6 Influence on flow patterns
- 7 Functional characteristics of emerged detached segmented breakwaters
- 8 Applicability of detached breakwaters
- 9 References
- 10 See also
Variable of breakwater schemes
Breakwater schemes have many variables, which determine the impact on the shoreline. The variable parameters are outlined in the following:
- Emerged, submerged or floating
- Distance from shoreline and location relative to the surf-zone
- Length and orientation
- Single or segmented
- Special shapes
There are further descriptions later in the article of combinations of all these parameters.
Purpose of a breakwater
A shoreline management breakwater serves two purposes:
- To provide shelter from the waves
- Through this shelter, to manipulate the littoral transport conditions and thereby to trap some sand
Some breakwaters, offshore breakwaters, are constructed in deep water as a special type of port, providing shelter for a piled berth connected to the coast by a piled jetty. This kind of port is normally used when the slope of the coastal profile is very gentle, which makes the construction of a traditional port very costly. The philosophy is that the distance to the shoreline behind this kind of port will minimise the impact on the shoreline. However, in practice, it is very difficult to construct such a zero impact port.
Defining a detached breakwater
A detached breakwater can be characterised by several parameters as shown in Fig. 1. below.
- Fig. 1. Definition of parameters characterising detached breakwaters and accumulation forms.
The most important parameters are:
- LB Length of the breakwater
- x Breakwater distance to shoreline
- x80 Surf-zone width, approximately 80 % of the littoral transport takes place landwards of this line
Dimensionless length and distance:
- LB* = LB/x Breakwater length relative to breakwater distance to shoreline
- x* = x/x80 Breakwater distance relative to surf-zone width
- Salient: When the dimensionless breakwater length LB* is less than approx. 0.6 to 0.7, a bell-shaped salient in the shoreline will form in the lee of the breakwater. However, parameters other than the breakwater length and distance also influence the accumulation pattern.
- Tombolo: When the dimensionless breakwater length LB* is greater than approx. 0.9 to 1.0, the sand accumulation behind the breakwater will connect the beach to the breakwater in a tombolo formation. But again, parameters other than the breakwater length and distance influence the accumulation pattern
If there are several breakwaters in a series, this is referred to as a segmented breakwater, where the length of the gap between the breakwaters is denoted:
- LG Length of gap between breakwaters in a segmented breakwater
Functional characteristic of emerged detached single breakwaters
A detached breakwater provides shelter from the waves, whereby the littoral transport behind the breakwater is decreased and the transport pattern adjacent to the breakwater is modified. These characteristics of a breakwater are utilised in different ways for various types of breakwaters by varying relevant parameters. There are three different types of breakwaters, as can be seen in Fig. 2. below.
- Fig. 2. Types of detached breakwaters.
A detailed description of the following three types of detached breakwaters can be found below.
- Offshore breakwaters
- Coastal breakwaters
- Beach breakwaters
Offshore breakwaters are located far outside the surf-zone, x* > 3. The purpose of an offshore breakwater is normally to protect an offshore ship wharf against wave action, which means that an offshore breakwater is a special type of port. The offshore breakwater is used when the coastal profile is very flat. At such locations, a traditional port would have to extend far from the shoreline or extensive dredging works would have to be carried out to provide access to the port. In order to minimise the works and to avoid the associated impact, an offshore breakwater may be the answer. The offshore breakwater is normally located at a slightly greater water depth than is required for navigation, thus avoiding/minimising capital dredging and minimising sedimentation. The philosophy is thus threefold:
- First, to provide shelter for a wharf,
- Secondly, to minimise sedimentation, and
- Thirdly, to minimise the impact on the coastline.
The philosophy behind an offshore breakwater, in relation to its influence on transport conditions, is thus to place it as far away from the surf-zone as possible and make it as short as possible so that its impact on the coastal morphology is negligible. However, experience shows that this is very difficult to obtain in practice; offshore-detached breakwaters often cause accumulation in their lee zone resulting in erosion effects in adjacent areas. It is thus important that the coastal impact of offshore breakwaters is taken into account when carrying out an environmental impact assessment for a port. Offshore breakwaters will not be treated further in these Guidelines as offshore breakwaters are not used as shoreline management structures.
- Fig. 3. Sand accumulation forming a salient in the shoreline behind an offshore breakwater, Sergipe, Brazil. X* = 3.6.
The following two types of breakwaters are mainly used for shoreline management, where the inherent capability of a breakwater to manipulate the littoral transport is utilised.
Coastal breakwaters are located within a distance from the shoreline of half the width of the surf-zone, up to twice the width of the surf-zone, 2>x*> 0.5. Such breakwaters trap sand within the part of the littoral zone they cover, thus securing that part of the coastal profile against erosion.
- Fig. 4. Coastal breakwater, which has formed a tombolo, Covis Place, Sri Lanka. X* = 1.0.
Beach breakwaters are located within less than half the width of the surf-zone from the shoreline, x*>0.5. Beach breakwaters trap sand on the foreshore without interfering significantly with the overall transport pattern.
- Fig. 5. Beach breakwaters, The Danish West Coast. X* = 0.14.
The philosophy behind coastal and beach breakwaters is as follows:
- To partly provide wave shelter for a certain part of the shore and the coast
- To modify the littoral transport in predictable way, so that the combined shore-restoration and coastal protection function can be properly designed. The extent of the sand trapping, or the ability to establish the desired sand accumulation pattern, is mainly regulated by choosing the length of the breakwater, the distance of the breakwater to the shore and the number of single breakwaters in a segmented breakwater and, finally, the length of the gaps.
- The advantage of a breakwater in comparison to a groyne is that it is possible to modify the littoral transport in a smoother manner than for a groyne. In this way there will be less lee side erosion on the downstream shoreline. This applies especially to breakwaters, which are so short that a permanent tombolo does not develop.
Sometimes coastal breakwaters are planned so as to provide shelter for the beach landing of small fishing boats or sheltered water for swimming. This is difficult as sufficient shelter for the boats and the swimmers requires such a long breakwater that a tombolo develops. When the tombolo has developed there is no sheltered water area left for boat landing and swimming, only a semi-protected bay downstream of the tombolo is left. This bay may be suitable for landing small boats, but it is certainly not suitable for swimming during rough wave conditions due to the eddy, which will always be present during such conditions.
Sand will be trapped behind a breakwater if initial sand fill is not performed. The trapped sand comes from the adjacent beaches, which means that both the upstream and downstream beach will suffer from erosion during the development of a salient or a tombolo. When a tombolo has been formed, the adjacent beaches are influenced in a way similar to that of a groyne with upstream accretion and lee side erosion. The influence of a salient will be smoother.
Impacts of breakwaters
A detached breakwater has the following impact on the hydrodynamic conditions in the adjacent area:
- The breakwater shelters partly from the waves; however, as the waves diffract into the sheltered area, a complete shelter cannot be obtained. The longer the breakwater, the better the shelter. Submerged and floating breakwaters provide less shelter.
- Wave-overtopping of submerged or low breakwaters will cause an additional supply of water in the area behind the breakwater, and consequently some compensation currents running out the sheltered area.
- The wave set-up on the foreshore is less in the sheltered area than outside, which generates local currents towards the sheltered area along the foreshore from both sides of the breakwater so that two eddies develop. These eddies also develop in the case of oblique wave approach.
- The longshore current is partially blocked by the circulation currents; this causes some of the longshore currents to be diverted outside the breakwater.
- Fig. 6. Wave and current conditions at a detached breakwater with a perpendicular wave approach.
And the following impact on the morphological conditions:
- The littoral transport in lee of the breakwater decreases due to the attenuated wave and longshore currents in the area sheltered by the breakwater. This causes the trapping of sand behind the breakwater depending on the conditions. As a rule-of- thumb, the trapping of sand will develop into a tombolo formation connecting the breakwater and the shore by sand deposits, if the length of the breakwater is equal to or longer than 0.8 times the distance between the shore and the breakwater. For shorter breakwaters, only a salient in the shoreline will develop.
- The diversion of the longshore currents will cause the development of local erosion close to the heads of the breakwater.
- The trapping of sand, especially if a tombolo has developed, will cause lee side erosion downstream of the breakwater. This downstream erosion is very similar to what is developed for groynes. However, there are more parameters involved in breakwaters, so it is possible to manipulate the transport in a more refined manner.
- A breakwater traps sand under all circumstances, even if the net transport is zero. This means also that there will be a coastal impact in any case.
- Fig. 7. Initial sediment transport pattern and initial morphological impact caused by a detached breakwater for perpendicular wave approach.
When several breakwaters are constructed in a row, the system is referred to as a segmented breakwater. A segmented breakwater is used to protect long sections of shoreline; the downstream coastal impact will be correspondingly larger than for a single breakwater.
Other impacts by breakwaters:
- If segmented breakwaters are constructed with too small gaps, the water exchange in the embayments between the breakwaters may be poor.
- Breakwaters normally obstruct part of the view over the sea, which means that the visual impact can be unacceptable.
- Swimmers may feel tempted to use the sheltered area in connection with detached breakwaters, but the circulation currents can be dangerous.
Influence on flow patterns
The influence of various coastal breakwaters on the flow pattern of the longshore current is discussed in the following. Two breakwaters, one relatively long and the other one relatively short, are considered. Immediately after the construction of the breakwaters, the flow pattern is simulated by applying DHI’s numerical model system MIKE 21. Two modules have been applied, the parabolic mild slope wave module and the depth-integrated hydrodynamic module, MIKE 21 PMS and HD, respectively. The dimensions of the breakwaters are:
|The long breakwater||312 m||240 m||250 m||1.3||0.96|
|The short breakwater||144 m||240 m||250 m||0.6||0.96|
The bathymetry was a plane beach with constant slope of 1:50 Irregular and directional waves with: Hs = 2.8 m, Ts = 8.0 s and α0 = 12o were used.
The flow patterns for these two breakwaters are presented in Fig. 8. below.
- Fig. 8. Flow pattern for a “short” and a “long” breakwater, LB* =0.6 and LB* =1.3, respectively.
The long breakwater causes major changes in the flow pattern. There are increasing current speeds towards the lee zone, high current speeds close to the breakwater heads and circulation in the downstream end of the lee zone. This current pattern and the corresponding sediment transport pattern cause the formation of a tombolo. There will also be local scour close to the breakwater heads. The eddy in the lee zone will remain, even after the tombolo has formed, and the current around the upstream head of the breakwater will increase with a higher offshore component. The current eddy and the scour holes will be dangerous for swimmers, and the jet directed offshore will cause a loss of sand and decreased bypass, resulting in relatively large lee side erosion. The local lee bay will tend to collect seaweed and debris. Furthermore, the tombolo provides easy access to the breakwater, which is not practical, as walking on the structure and jumping from it can be dangerous.
If the breakwater is fairly short, the flow pattern will be quite different, as seen in the above figure. There will be no high currents at the breakwater heads; there will be only a minor tendency for eddy formation and there will be only slight changes in the general pattern of the longshore current. The morphological response to such a breakwater will be a smooth salient in the shoreline; a tombolo will not form and there will be no scour holes at the end of the breakwater heads. There will be no offshore loss of material, and the lee side erosion will be mild. These are all positive effects; the negative effect is that the protection, provided by a short breakwater, is limited. It will secure a wider beach locally, but it will not be able to stabilise a long section of shoreline by a stable sand filet. If the sand filet consists of nourished sand, frequent re-nourishment will be necessary.
The optimal solution is probably somewhere between a long and a short breakwater. It must form a solid salient, but not a tombolo. This solution is balanced between the requirements for coast and shore protection, the minimisation of downstream impacts and seaweed trapping, and the optimisation of safety. Other modifications to the breakwater can also be considered. This will be discussed under the heading: Modified breakwaters and headlands.
Functional characteristics of emerged detached segmented breakwaters
The above discussion was related to single breakwaters, but shoreline management schemes often utilise segmented breakwaters. A segmented breakwater scheme provides many possibilities, ranging from total coastal protection to mild shore protection. Fig. 9. below shows the characteristic shoreline development, which can be obtained with segmented breakwaters with various combinations of breakwater lengths and gap widths.
- Fig. 9. Characteristics for various segmented breakwater schemes.
A mixture of seawalls, revetments, groynes and breakwaters has, in the past, often been used in densely populated areas as coastal protection against long-term erosion. In some places the protection was co-ordinated, but most often it was everybody’s individual fight against the sea. Such areas are characterised by lost beaches, poor passage along the coastline and poor aesthetic appearance. The natural beauty of the coastal landscape is lost due to coastal protection measures and erosion continues. Such areas require an urgent upgrade to secure the values behind the coastline, as required by the landowners, and to re-establish the shore to the highest possible level, as required by the public and the authorities. This calls for a well co-ordinated shoreline management scheme. With modern techniques and sufficient funds, it will be possible to upgrade the spoiled coastline to a nearly natural condition. However, it is almost impossible to re-establish the active coastal cliff, which is also a valuable coastal resource. The only way to achieve this is to allow the natural coastal erosion to continue. However, this requires that the authorities purchase the coastal land and allow it to develop naturally. In most cases this is unrealistic, but one solution may be to leave public-owned sections without protection, provided they are of a suitable length.
In such heavily populated and mostly privately owned areas, it will normally not be practical to choose a solution using nourishment alone, as it will not provide sufficient safety against coastal erosion, and as it is also difficult to manage. In this case a segmented breakwater scheme is a good choice, and it can be tailored to suit the requirements agreed upon by the interested parties. A pure nourishment solution requires substantial public involvement.
The numerous possibilities are illustrated by the three very different schemes sketched in Fig. 9. above. It is evident that nearly all combinations of requirements can be met. The most difficult aspect of such projects is often the public and political process, which has to be carried through to reach consensus. The importance of this process must not be underestimated in the planning process.
Applicability of detached breakwaters
It is evident from the above that breakwaters are able to protect sections of shoreline in a more diversified and less harmful way than groynes, but some of the disadvantages of groyne schemes also characterise breakwater schemes. It has been demonstrated that, on some types of coast, breakwaters function differently to groynes. A breakwater can, for example, trap sand on a coastline with a perpendicular wave approach, which is hardly the case for a groyne. The applicability of breakwaters to different types of coasts (see:coast types) is discussed in the following:
Type 1 coasts
Breakwaters can be used on 1M and 1E type coasts in a way similar to groynes, namely to prevent the loss of sand into adjacent sections. When groynes are used in this way, they will hardly trap any sand and there will hardly be any lee-side erosion. When breakwaters are used on type 1 coasts, they will trap sand in their lee areas, which causes local erosion on both sides of the breakwaters. This can be avoided if the sheltered areas behind the breakwaters are filled in as part of the project. In addition to this local erosion, adjacent to the breakwaters, a little additional erosion occurs on either side of the protected section, due to the lack of sand from the protected section.
Single breakwaters or segmented breakwaters can both be used as direct protection of specific sections against shore erosion and against coast erosion if they are combined with initial sand fill.
Type 2 and the most perpendicular part of type 3 coasts
Like groynes, breakwaters are applicable on coasts of type 2M and 2E and on the parts of the 3M and 3E coasts, which have an angle of incidence close to that of the type 2 coast. The breakwaters accumulate sand both on their upstream side and in their sheltered zones as a tombolo or as a salient, depending on their characteristics. The upstream accumulation will be very similar to that of a groyne if the breakwater is so long that it forms a tombolo. If this is not the case, the upstream accumulation will be smaller. Both the sand accumulation in the sheltered zone and the upstream accumulation will take place at the expense of lee side erosion on the downstream side of the breakwater scheme. In order to minimise the downstream erosion within the scheme, it is important to include the initial filling of the scheme in the construction project.
Local erosion and scour will occur near the breakwater heads, and the outer part of the coastal profile will continue to erode unless the breakwaters cover the entire littoral zone. Beach breakwaters will eventually collapse if their sea sides are not strengthened, whereas coastal breakwaters constructed at a distance greater than say x*>1.2 will not be exposed to an eroding seabed.
Lee side erosion and profile steepening effects of segmented breakwater schemes can be mitigated by regular nourishment, but regulating the length of the individual breakwaters in the scheme can also partly mitigate the extent of the lee side erosion. The combined use of segmented breakwaters and nourishment secures against erosion of the beach in the gaps, but also to some extent against coastal erosion in the areas directly protected by the breakwaters. This means that a segmented breakwater scheme combined with nourishment has to be further supplemented with revetment protection in the gaps in order to provide complete coastal protection.
It is recommended to use few large structures instead of many small structures in order to enhance the aesthetic appearance of a segmented breakwater scheme. This is especially true for type 2 coasts, as the individual breakwaters are capable of suspending long upstream sand filets - see Fig. 10.
- Fig. 10. Upgrading of a worn-out protection scheme at a type 2E coast (upper part) with a breakwater scheme consisting of a series of singular large coastal breakwaters with long spacing combined with initial nourishment (lower part).
Type 4 and 5 coasts and the most oblique part of type 3 coasts
A single structure parallel to the coast is not very efficient when the waves are fairly oblique to the shoreline, as the effective length of the structure perpendicular to the wave direction is relatively small is this case. As the sand filet accumulation for these types of coasts is very short, single breakwaters cannot be recommended.
Segmented breakwater schemes with relatively short gaps can be used as a combined shore and coastal protection measure on all types of coasts because the formation of pocket beaches in the gaps does not depend very much on the wave direction when the gaps are small.
General comments on emerged breakwaters
- Breakwaters tend to trap seaweed and floating debris in the bays, which are formed on the upstream side as well as on the lee side.
- A breakwater does not constitute an obstruction for the passage along the beach.
- Breakwaters are dangerous to walk on and should be constructed so that only a salient is formed.
- The lee zone eddies are dangerous for bathers.
- Breakwaters constitute a foreign element in the coastal landscape as they obscure the view of the sea, but if their number is minimised, and they are built relatively far from land, this problem is minimised.
- The disadvantages of breakwaters and groynes can, to some extent, be avoided by optimising the shape of the structures. This is the subject of the next subsection.
Author: Karsten Mangor, DHI, 2004. firstname.lastname@example.org.
All content is written by Karsten Mangor unless referenced otherwise. Full source: Mangor, Karsten. 2004. “Shoreline Management Guidelines”. DHI Water and Environment, 294pp.